Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Don't take too lightly the forklift at the workplace. If the procedure is not good, there will be severe mishaps in mins, and there are many accidents involving forklifts.

Instance 1: The forklift cargo blocked the chauffeur's view, and the individual ahead can not be discovered, leading to a moving accident.
Case 2: In order to keep the balance of the forklift when raising heavy products, the staff members used their body weight as the counterweight, which nearly triggered casualties.
Situation 3: The size of the forklift freight surpasses the allowable width of the route and holds on the roadside rack, which practically creates an crash.
Instance 4: Forklift is speeding and rolls over throughout a turn.
Case 5: The forklift driver did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the personnel unlawfully, the forklift chauffeur does not use the seat belt, the forklift lifter falls and the chauffeur is crushed when the forklift surrender.
Instance 7: The forklift chauffeur did not put on a safety belt and dropped from the car when it rolled over and was squashed.
Forklift procedure must pay attention to these matters ：.

Begin.
1. Prior to beginning, observe the environments, and after validating that there are no barriers that prevent the safety and security of driving, beep the horn initially and after that begin.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress ( atmospheric pressure) gauge must be risk-free prior to starting.
3. When the forklift starts with a load, the chauffeur should initially validate that the tons is steady and trusted.
4. The beginning needs to be slow-moving and stable.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be maintained 300mm-400mm, and the pole must be slanted backwards. .
2. Do not lift the fork too high when driving. When getting in and leaving the task website or while driving, take care that there will be no obstacles overhead. When the tons is traveling, the fork must not be elevated too expensive, which will impact the stability of the forklift. .
3. After unloading, the fork ought to be decreased to the regular driving setting prior to driving. .
4. When turning, if there are pedestrians or lorries nearby, the driving signal needs to be released initially. High-speed doglegs are restricted. High-speed sharp turns will certainly trigger the vehicle to shed lateral security and tip over. .
5. When the forklift is downhill, it is strictly restricted to shut off the fire and slide, and it is forbidden to brake unexpectedly while driving with lots unless there are special circumstances.
6. When the forklift is running, it has to follow the website traffic rules in the factory and should keep a particular safety and security range from the car in front. .
7. When the forklift is running, the lots has to be in the most affordable position that does not impede the driving, and the gantry must be effectively tilted back. The load shall not be raised other than when piling or loading. .
8. The height of the tons need to not obstruct the driver's sight. In special scenarios, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the factory area is 5 km/h, and it should drive safely at a reduced rate when getting in the manufacturing workshop area. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If issues are found, they will certainly be repaired and reported in a timely way, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the distance in between both forks ought to be adjusted as needed to make the tons of both forks well balanced and not skewed, and one side of the thing should be against the shelf. .
2. It is restricted to collaborate with a solitary fork or utilize a fork top or draw. In unique circumstances, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process Electric Forklift Truck for Warehouse of packing and discharging products, the forklift needs to be braked with the brake. .
4. The rate of the automobile should be slow and consistent. Take care not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as possible under the lots, and it ought to be kept in mind that the fork pointer must not touch other products or objects. The tons should be supported with very little back tilt of the gantry so that the lots does not move in reverse. The mast can be tilted forward a little when the lots is reduced to allow for easy placement of the lots and extraction of the forks. .
6. It is restricted to fork products at broadband and collide with difficult objects with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding avoid the collapse of the goods and injure people. .
8. Straining is prohibited, and it is forbidden to make use of forks to raise employees to engage in high-altitude operations to stay clear of high-altitude falling mishaps. .
9. It is not allowed to make use of the brake inertia to slip, put, round or roll things. .
10. It is not enabled to utilize forks to pick, transform pallet dump.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork impend. Before leaving the forklift, you must dump the goods or reduced the fork frame.
2. Draw the parking brake handle to dead or depress the hand brake button.
3. The engine is switched off and the power is removed. (Except for special circumstances, such as the chauffeur does not leave the vehicle's line of vision and does not go beyond 1 min).
4. Remove the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance must be examined, and gas, lubricating oil and cooling water need to be included.
2. Inspect the security efficiency of beginning, running and braking.
3. Inspect whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature level are regular.
5. After the forklift is running, the exterior leak needs to likewise be inspected and the seals ought to be changed in time.

Forklift Safety Operation Specifications.
1. You have to check prior to leaving the automobile;.
2. When you experience someone before you during driving, you must send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the low point of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be too sharp to avoid the propensity of " totally free turning";.
6. Adding and down the incline needs to be slow and consistent, and no switching on the slope is allowed.
7. Do not drive throughout the slope. When the slope is greater than 10%, the lorry ought to be driven backwards when worsening;.
8. When the forklift workers carry the goods and progress, if they experience big or heavy goods and go to the driver's view, they must take the turning around workout
.
The "Eight Prohibitions" must be adhered to in the operation.
1. Single fork procedure is not enabled.
2. It is not enabled to lift the goods for far away driving.
3. It is not permitted to get the goods by passing on the pallet with the fork.
4. It is not enabled to directly shovel chemicals, flammables and other hazardous chemicals with forks.
5. It is not permitted to make use of inertia pressure to grab the goods.
6. It is not allowed to make use of stopping pressure to exile round or easy-to-roll objects.
7. It is not permitted to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive laterally on inclines
.
Vehicle parking is not allowed under the list below conditions.
1. Contours, narrow roads, train crossings;.
2. Sections with a longitudinal incline above 5%.
3. When there is an challenge on Stand-on Electric Pallet Stacker one side of the road, the contrary side of the section with the exact same size as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844